> For the complete documentation index, see [llms.txt](https://docs.xbstation.com/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://docs.xbstation.com/xblink-4g-r3/user-manual/getting-started/setup.md).

# Setup

This section contains the hardware connection of XBLink 4G R3.

XBLink 4G R3 hardware connection mainly includes SIM, Antenna, XBCamera V2, Flight Controller and Power up.

### Nano SIM Card <a href="#sim-card" id="sim-card"></a>

XBLink 4G R3 supports push-push NanoSim connector.

Insert your SIM card into the SIM Card slot, the chip contacts have to **face up**.

<div align="center"><figure><img src="https://752643261-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F-M1Ot9F_Ob2Aboz1SKNK%2Fuploads%2FW5xoICedWbBVjTLcfYLK%2F2%20(44).png?alt=media&amp;token=0d5f20a6-39b2-47c6-8d07-b4174c2a298a" alt="" width="563"><figcaption><p>SIM Card must be faced up</p></figcaption></figure></div>

{% hint style="info" %}
The SIM card is recessed into the enclosure and you might need a tool to push it into the socket. You can hear a click when the card is inserted.
{% endhint %}

To remove the SIM card, gently push it further into the slot using a tool until you hear a 'click', then release. The card will pop out for removal.

### Antenna <a href="#antenna" id="antenna"></a>

Connect the two LTE antennas to the MMCX connectors.

<figure><img src="https://752643261-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F-M1Ot9F_Ob2Aboz1SKNK%2Fuploads%2Fu8yqXTXhFNYPlNG5KEHt%2F2%20(45).png?alt=media&amp;token=c843fb96-ad5d-46cb-aa2c-4f3c04b43fed" alt="" width="375"><figcaption><p>Connect LTE Antennas to XBLink 4G R3</p></figcaption></figure>

{% hint style="danger" %}
**Note:** Be careful with the antenna port. Remove or Install it in a **straight angle**.

**We are not responsible if the antenna is damaged due to physical impact**
{% endhint %}

{% hint style="info" %}
**Antenna installation and removal instructions:** [**here**](https://www.youtube.com/watch?v=lAXGtti88gc)
{% endhint %}

### XBCam V2

Connect XBCam V2 to USB type C port.

<figure><img src="https://752643261-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F-M1Ot9F_Ob2Aboz1SKNK%2Fuploads%2FAyEVVO4HgIffKWwEjlQi%2F2%20(46).png?alt=media&amp;token=f1a9aedc-6756-454f-8bd9-4d1ae682eb5f" alt="" width="375"><figcaption><p>Connect XBCamera V2 to XBLink 4G R3</p></figcaption></figure>

{% hint style="danger" %}
Please don't connect any HDMI cameras like Gopro,... to **CSI port**. This is **CSI** not **HDMI port**.
{% endhint %}

{% hint style="info" %}
**Note:** We currently support variety of Cameras and Gimbals in [**here**](https://docs.xbstation.com/xblink-4g-r3/user-manual/advanced-configuration/cameras-and-gimbals.md)

For another payload via **CSI** or **HDMI**, please contact us.
{% endhint %}

### Connect Flight Controller (Telemetry)

You can use Telemetry 1 or 2 of Pixhawk for connection with XBLink 4G R3 via [**COM1**](https://docs.xbstation.com/xblink-4g-r2/user-manual/getting-started/interfaces.md#com1-aux-j3) port.

<div><figure><img src="https://752643261-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F-M1Ot9F_Ob2Aboz1SKNK%2Fuploads%2FZPNdTMTDz6NuCR58CeiT%2F2%20(47).png?alt=media&amp;token=abcdcb31-c767-47ab-beb1-26c11b79691b" alt="" width="427"><figcaption><p>Connect <em>Pixhawk</em> to XBLink 4G R3</p></figcaption></figure> <figure><img src="https://752643261-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F-M1Ot9F_Ob2Aboz1SKNK%2Fuploads%2FFQFTqjtibZrJpTB9fW7z%2F2%20(48).png?alt=media&amp;token=1c29560c-d07a-445c-bf05-224764227eec" alt=""><figcaption></figcaption></figure></div>

{% hint style="info" %}
**Note:** Config baud rate of Pixhawk to 57600, SERIAL1\_BAUD (Default 57, it means 57600), SERIAL1\_PROTOCOL: 2 (MAVLink 2)
{% endhint %}

### Power up

XBLink 4G R3 supports 7-30V voltage input. We highly recommend **3-4 S battery or 12V DC UBEC** (minimum 3A) to power (6S battery is possible but make sure it's high quality and low discharge)

<figure><img src="https://752643261-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F-M1Ot9F_Ob2Aboz1SKNK%2Fuploads%2FT6zfaJ4hmrzUkDlhobxk%2F2%20(49).png?alt=media&amp;token=0c17b3ca-b86d-4686-b4e8-38b994c2decf" alt="" width="285"><figcaption></figcaption></figure>

{% hint style="danger" %}
If you use low quality or high discharge 6S battery for drone, we are not responsible for damage.
{% endhint %}

### Done

<figure><img src="https://752643261-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2F-M1Ot9F_Ob2Aboz1SKNK%2Fuploads%2FTmsclsZtOJWoswp4EgLr%2F2%20(50).png?alt=media&amp;token=ddfd07ce-88c8-4d9d-9a1b-5395ebdf3957" alt="" width="285"><figcaption><p>Completion of setup XBLink 4G R3</p></figcaption></figure>

Once XBLink 4G R3 has green color continue to the next step to connect it to [XBStationPillotApp](https://docs.xbstation.com/xblink-4g-r3/user-manual/xbstationpilotapp.md).

More information: [here](https://www.youtube.com/watch?v=20M-ikx_jjE)

{% embed url="<https://www.youtube.com/watch?v=20M-ikx_jjE>" %}
